Livestock Operation
Type of livestock : Cattle, Dairy, Poultry, Hogs, Horse, Goats, Sheep, etc.
Type of Grain: Barley, Corn, Oats, Wheat, Millet, Peas, Lentils, Pulses, etc.
Groove Pattern: 1 to 14 gpi. ( Other groove pattern available)
SVENMILL™
50 to 5000 head

Avg Capacity (bu/hr)* Dimensions Weight. Rollers Size Motor Suggested
Corn - Barley - Oats W / H / L lbs W x D HP Herd Size*
SvenMill 4 125 - 90 - 60 18"/38"/48" 400 4" x 11" 2.0 50-75
(3.2T to 1T)
SvenMill 6 150 - 120 - 80 20"/38"/48" 475 6" x 11" 3.0 75-125
(3.8T to 1.3T)
SvenMill 8 185 - 150 - 100 24"/38"/48" 525 8" x 11" 5.0 150-250
(4.7T to 1.6T)
SvenMill 12** 250 - 200 - 130 30"/38"/48" 640 12" x 11" 7.5 250-275
(6.3T to 2.1T)
SvenMill 16** 325 - 250 - 160 36"/38"/48" 725 16" x 11" 10.0 275-350
(8.2T to 2.6T)
SvenMill 20** 375 - 300 - 225 38"/48"/48" 800 20" x 11" 10.0 350-450
(9.5T to 3.7T)
SvenMill 24** 575 - 450 - 300 42"/48"/48" 950 24" x 11" 20.0 450-750
(14.6T to 4.9T)
SvenMill 30** 750 - 600 - 400 46"/48"/48" 1200 30" x 11" 30.0 750-2000
(19.0T to 6.5T)
SvenMill 36** 1250 -1000 - 650 54"/52"/54" 1600 36" x 13" 40.0 1000 and up
(31.8T to 10.6T)


** These SvenMill model are available in a PTO portable version that includes, PTO shaft, trailer and either a drag auger or a hydraulic up auger.


EconoMill™


Up to 75 head
Avg Capacity (bu/hr)* Avg Capacity (bu/hr)* Dimensions Weight. Rollers Size Motor Suggested
Barley/Oats Barley/Oats. W / H / L lbs W x D HP Heard Size*
(Head)
EconoMill 1.5 50/35 115/90 22"/34"/40" 275 6" x 8" 1.5 Up to 60
​
EconoMill 2.0 60/45 150/120 22"/34"/40" 280 6" x 8" 2.0 Up to 75
​
Avg Capacity (bu/hr)* Dimensions Weight. Rollers Size Motor Suggested heard
Barley W / H / L lbs W x D HP size
MicroMill 10 18"/21"/38" 55 3" x 6" 3/4 up to 10
* Please note all technical data are approximations and are subject to change. Capacity data vary widely depending on type of grain milled, moisture content and other variables. Before making decisions based on technical data shown, you should contact us to insure proper use. Max capacity data is provided to help comparison with other brands.

WE HAVE BEEN MAKING ROLLER MILLS FOR OVER 45 YEARS!
For many years roller mills have been used to crack grains to feed livestock. There are many advantages to roll grain directly of your farm/feed lot.
The power used to operate SvenMill roller mills is far less than a PTO tractor. An average cost of an electric motor powered mill is approximately $0.60 an hour versus approximately $60.00 an hour for a PTO drive off a modern tractor.
Cracking grains with a roller mill fresh at the farm increases the quality of the feed and therefore the health of animals.
The SvenMill roller mills crack the grain instead of pulverizing it like a hammer mill. This allows for less fines and flour and more nutrition going to the animals.
All SvenMills comes with features built for feeding livestock in the most extreme environments.
The SvenMill comes with a slotted frame which allows for easy removal of the rolls for regrooving.
​
The Instant Release lever allows for quickly disengaging the rollers and cleaning or, in the case of a power outage, empty the grains and start again in minutes.
The Offset roller configuration allows bigger particles to be pulled in the opening efficiently and increase capacity.
​
The thick welded steel plates used for the frames of the SvenMill are what makes it the industry leader it has been for 45 years. We still see our original mills coming to the factory for maintenance.
​
"At Apollo Machine, we know you are out there in the middle of the winter using our mill and we try to make your experience as efficient as possible"